Hi all,

The threading above the grip recently came undone om my SMG carbon.  It was severed and came undone after loosing an arrow:













Should I simply remove the threading and re-thread?  What type of threading is this anyway?

377

(18 replies, posted in Bows)

Ok I got everything I need to brace with dojigae.  I'll likely do a second attempt this weekened.  So for the bow, when pulling it back on the bracing board, how supple should it be?

Supple enough that it can be pulled back and tied to the other dojigae w/ very little resistance almost like rubber pipe?


It looks like the gentlman in this video heats his bow till the sinew glistens a little.  I'd imagine the surface is very warm at this point.  His bracing seems rather fluid with slight tension:

http://www.youtube.com/watch?v=AjPOkPl5jQg

378

(18 replies, posted in Bows)

sissara wrote:

big_smile Good luck with your bracing.

Thanks sissara but chickened out just now.  The limbs felt a little too stiff and it cooled off considerably today.  So the bow was more on the cool side.  Unfortunately the Mid-Atlantic climate where I live in is notorious for this.  I keep the box out in the garage so that's why it is so susceptible to temperature change.  I know from leaving my horn bow out in the sun for just 10 minutes how supple the bow can get from just that and the limbs weren't like that and too cool. 

Actually if I could just get a little clarification on how warm the bow should feel that would help a lot.  I may modify the heat box slightly to meet requirement.

379

(18 replies, posted in Bows)

Thanks all again for your answers and comments.  Today I just finished building the bracing device.  I also assembled a heat box and have had the bow in it since about 2pm today.  I may brace for the first time tomorrow but have just a paragraph below of questions/concerns:

I have the heat box insulated with aluminum foil in order to generate heat to the bow.  The heating source is not a low watt light bulb but actually a low watt heating pad (8 watts) placed on a wood block that is slightly suspend above the block w/ 4 little suspension pads.  It is placed in the center of the box laying in between the bows limbs just above the grip.  The bow is now luke warm but not overly warm.  I used the heating pad because it was less involved then a light bulb set up and was a little paranoid that the bulb would generate too much heat (its also very hot where I live now) and cause de-lamination.  Temperature in box is about 78 degrees F.  So I was wondering how hot the bow should feel after a day in the heat box?  Should it have a luke/mildly warm feel or more of a heated feel to it?  Should I expect it to be more supple when bracing or still with quite a bit of tension?

Sorry for the long windedness of this but I really would like to do the bow honor and make things right.

Matt

380

(18 replies, posted in Bows)

Thank you Thomas.  For gluing the grip material to my bow should I use a modern adhesive or traditional (fish glue, hide glue)?

381

(18 replies, posted in Bows)

bluelake, sissara,

Many thanks.  This will actually be my second horn bow though I admit my instructions recieved for proper handling for the other one were nowhere near as intense as for the gung.  But the reflex for the other one is nowhere near as extreme.

Yes I certainly don't want to report any bad news.  I have much respect and interest in the sport of archery, particularly traditional aspects and even more particularly for the Asiatic composites.  That's what got me into this sport years ago.  I am just now starting to aquire horn composites. 

The gung appears to be quite the challenge.  They are regarded by quite a few bowyers of the horn composite tradtion as the best.  So naturally I had to get one. 

I will perhaps make a local inquiry around where I live to see if anyone participates in traditional Korean archery.  There are Korean communities around but I suspect I'd have to go to N. VA to likely find a Korean traditional archery group.

Best,

Matt

Hi All,

I have just entered the world Korean Archery today as I received my first Korean carbon bow by SMG and a traditional Korean horn bow.  I would also like to thank Mechwar for making all this possible.  It was an absolute pleasure doing business with you.  Also the amount of care that the Korean's put into their archery traditions is second to none.  I am already very impressed with how I received my bows and the craftsmanship.  Few questions though regarding proper care, maintenance, and stringing for my horn bow.

1) It is recommended to use a heat box before stringing.  I haven't built one yet but was curious if there was a tutorial on how to make one.  Also, is the standard protocol for it to be left in the box every 5 days and if so how long?

2) Is there an alternate approach to the heat box method like say using Colemen propane burners to heat the bow before stringing?  If so, how long should bow be heated over source and how far away?

3) Is it always necessary to use the Dojigae or can one sometimes string it like this man did towards the end of the video:

http://www.youtube.com/watch?v=AjPOkPl5jQg


4) I was given wrapping material for the grip of my bow (see below).  To adhere the material to the handle, what type of adhesive should I use.  Hide glue maybe?


Any help would be greatly appreciated.  Thanks and best regards.

Matt

https://i.imgur.com/Nnx5hH7.jpg